Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

烧结时间对含铅玻璃制备微晶玻璃析晶及性能的影响

以铅玻璃与粉煤灰为原料，通过协同熔炼制备了微晶玻璃。通过XRD和SEM等手段研究了不同烧结时间下微晶玻璃的物相组成及显微结构，测定了微晶玻璃的密度、吸水率、维氏硬度和化学抗性。结果表明: 延长烧结时间对含铅玻璃加入量为40%(FG40)、50%(FG50)样品的晶相类型和晶化程度有影响，而对含铅玻璃加入量为60%(FG60)、70%(FG70)和80%(FG80)样品的影响较小。随着烧结时间延长，样品晶化程度提高，晶体长大，玻璃相减少。适宜的含铅玻璃加入量为50%~70%，对应的FG50、FG60、FG70样品最佳烧结时间分别为4 h、3 h、3 h。     

Fluoride-mediately solvothermal synthesis and tunable photocatalytic selectivity of urchin-like ZrO2 hollow microspheres

Photocatalysts often show excellent performances on the basis of their surface state of exposed faces with high reactivity, but unfortunately surfaces of this type are usually concealed into the interior of crystals for their high surface energy. We report here a possibility that for fluorine-terminated surfaces of monoclinic ZrO₂, these higher-energy surfaces could be retained and exposed. Urchin-like ZrO₂ hollow microspheres (UZHS) composed of nanoribbons with exposed (010) facets are obtained through a fluoride mediately solvothermal method. We prove the stabilization effect of fluorine adsorption on (010) facets by density functional theory calculations. More interestingly, UZHS exhibit tunable photocatalytic selectivity in dye degradation. The fluorinated UZHS exhibit good performances both on decomposing Congo red (CR) and methylene blue, while the surface-modified UZHS by calcination only favor decomposition of CR.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

Fabrication and characterizations of Cr3+-doped ZnGa2O4 transparent ceramics with persistent luminescence

0.5 at.% Cr:ZnGa₂O₄ precursor was synthesized by the co-precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low-agglomerated Cr:ZnGa₂O₄ powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa₂O₄ ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post-treatment at 1100℃ for 3 h under 200 MPa Ar. The in-line transmittance of 0.5 at.% Cr:ZnGa₂O₄ ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa₂O₄ ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa₂O₄ transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m² after 30 min, which is far superior to that of Cr:ZnGa₂O₄ persistent luminescence powders.     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。